2024 Toro Greensmaster® TriFlex™ Series 3320 (04530)

Information

2024 Toro Greensmaster® TriFlex™ Series 3320 (04530)

The Greensmaster® TriFlex™ Mowers were designed to take precision cutting on a greens mower to a completely new level. Adopting the proven Flex suspension, the cutting units float freely over contours and undulations of the green resulting in a superior quality of cut and aftercut appearance. Improved serviceability is another major advantage of the TriFlex™ models. The tool-free, quick-change cutting units make servicing the cutting units fast and easy and a lift-gate footrest provides easy access to the center cutting unit.

Features may include:

Stored Energy
  • A single operator can go from cutting Greens at 0.125" (3.2 mm) to cutting a Fairway at ¾" (19 mm) in just minutes. The tool-free, quick-change cutting units make it as easy as 1-2-3.
Lift-In-Turn Cutting Units
  • Easy access to the center cutting unit facilitates routine maintenance and repairs, simplifies adjustments, and eliminates the need to put the traction unit on a lift for cutting unit service saving you time, money, and frustration.
Faster Transport Speeds
  • The dependable Turf Guardian™ leak detection system provides immediate audio and visual indication of possible hydraulic fluid leaks.
DPA Cutting Units
  • Easily customize clip for different heights of cut and adjust other operational settings to gain complete machine control. Common operation information displayed includes: reel speed, hours of function, system voltage for reels, diagnostic descriptions, and much more.
Tool-Free, Quick-Change Cutting Units
  • With more than enough horsepower and highly efficient components, the TriFlex Hybrid models operate efficiently in energy savings mode. While in this mode, engine RPM's are reduced and the all-electric reel drive maintains a constant reel speed. This results in reduced fuel consumption and noise while maintaining quality of cut, performance, and productivity.

Photos

Highlights

  • Owatonna, Minnesota
  • 2024
  • Toro
  • Greensmaster® TriFlex™ Series 3320 (04530)
  • Briggs & Stratton® Vanguard®
  • 48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V-1100 watt brushless permanent magnet reel motors with separable controller.
  • Hybrid - Gas
  • Available
  • 80.83" (205 cm) | of Cut Range: Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is 0.062" - 0.297" (1.6 - 7.5 mm). With high HOC kit, range is 0.297" - 1.0" (7.5 - 25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

Specifications

  • 2024
  • Toro
  • Greensmaster® TriFlex™ Series
  • 3320 (04530)
  • Zero-Turn Mower
  • Briggs & Stratton® Vanguard®
  • Air Cooled
  • 23hp (17.2kW) @3600 rpm
  • 2920 rpm
  • 38.3 cu-in. (627 cc)
  • Hybrid - Gas
  • Hybrid | Implement: 48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V-1100 watt brushless permanent magnet reel motors with separable controller. 4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis. | Traction Drive: 2WD
  • No-tool quick adjust steering arm position with power assist allowing a wide range of operator sizes. Steering cylinder has a through shaft design for precise straight line tracking.
  • 2WD parallel hydrostatic
  • Off - On
  • Hand-actuated parking brake lever with two 6" (15.2 cm) diameter drum brakes mounted on the front wheel motors.
  • 12V
  • 12-volt lead acid, group size U1, with 300 minimum CCA at 0° F and 34 minutes reserve capacity at 85° F / 25 amps draw. 50 amp alternator. Seat switch.
  • 48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V-1100 watt brushless permanent magnet reel motors with separable controller.
  • 19" x 10.5" - 8", 4-ply, Smooth Tread
  • 19" x 10.5" - 8", 4-ply, Smooth Tread
  • Ground Speed - Forward: 0 - 10 mph (0 - 16.1 km/h) | Mowing Speed: 0 - 5 mph (0 - 8 km/h)
  • 48-volt system is isolated from 12-volt including the frame/chassis.
  • Sound Power: Sound level of 80 dB(A) at operator’s ear under normal conditions.
  • Blade: 5" (13 cm) | Weldment shaft: 1.375" (35 mm) | Reel Diameter: 5" (13 cm)
  • Blade: 21" (53.3 cm) | Product: 98" (249 cm)
  • 4.5" (11.4 cm)
  • 80.83" (205 cm) | of Cut Range: Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is 0.062" - 0.297" (1.6 - 7.5 mm). With high HOC kit, range is 0.297" - 1.0" (7.5 - 25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
  • 70.84" (180 cm) with reels
  • 47" (119 cm)
  • 59" (150 cm)
  • 6 U.S. gal. (22.7 L)
  • 1,257 lbs. (570 kg)
  • Bedknife: Replaceable single edged EdgeMax™ Microcut Bedknife is standard. | Blade Style/Type: Reel | Number of Blades: 11, 14, 8
  • Cutting Unit Type/Configuration: Triplex, balanced cutting units with precision die-cast aluminum cross member with two bolt-on die-cast aluminum side plates. Cutting units feature quick disconnect for removal/installation and are interchangeable to all positions. Double A-Arm Suspension utilizing sealed ball joints allows free cutting unit motion in pitch and yaw. Links system for the roll. The basket is directly mounted to the cutting unit displacing weight evenly over front and rear rollers. (patented)
  • InfoCenter™: Onboard LCD shows gages, alert/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake status, reel speed setting, backlap control. Clip control setting.